Skip to content

How to install a new toilet according to plumbing experts

To install a new toilet always comes good advice from hamilton plumbing experts if you consider that one of the most popular ways to add value and comfort to current homes is to remodel the bathroom. Bathroom remodeling projects almost always include removing the old toilet to install a new toilet, which can become a dirty and frustrating task. Follow these expert tips to install a new toilet flawlessly.

Remove the old toilet

One of the expert tips for installing a new toilet is that before installing the toilet, shut off the water supply to the tank with the wall shut-off valve. Do not remove the feed tube yet, otherwise the water in the tank will wet the floor. Discharge the toilet by holding the lever down until as much water as possible has been drained. Then lift the top of the tank and use a sponge to remove the remaining water. Use a sponge and container to remove the remaining water from the bowl.

Unscrew the supply tubing from the seal, placing a small towel underneath to absorb the water. Since you will be discarding this tubing, you can use adjusting pliers to close the circuit. Remove the bolt covers from the toilet base to expose the mounting bolt nuts. If they are rusty and difficult to remove, use a metal saw or cut-off wheel plumbing.

When removing the toilet, the gasket gasket will be dirty, so protect the floor by covering it with plastic or protective sheeting. If the toilet is attached to the floor with caulk, swing it slowly to break the toilet seal. Lift the tank and toilet carefully and place them on top of the plastic or take them out of the building.

Plug the exposed drain hole to prevent gases from escaping into the room. Be sure to use a cloth or other material that cannot fall into the drain pipe. Use a putty spatula to remove any old wax seal that may remain on the mounting flange. Also, clean any remaining caulk from the floor plumber.

Install New Toilet

Another expert tip for installing a new toilet is to thoroughly clean the area and make sure the mounting surface is level before installing the new toilet.

If the tank hasn’t been attached to the bowl yet, it will be easier to fit the toilet. Reverse the bowl (place a padded protection on the floor to protect the floor and the edge of the toilet bowl) and press the wax ring into place with the plastic sleeve away from the toilet. The sleeve goes into the mounting flange and drain pipe as hamilton plumbers do.

Insert the mounting bolts into the mounting flange using putty to keep them upright and properly aligned. Remove the drain hole plug and carefully lower the bowl over the bolts. Push the toilet bowl down firmly and evenly to compress the wax ring. Never swing the toilet to compress the wax ring as this can cause leaks and uneven compression.

Place the plastic retaining washers over the bolts, followed by the flat washers. Tighten the nuts by hand. Then, using a hex wrench, tighten the nuts twice on one side and twice on the other. Continue until the nuts are secure but do not overtighten or the toilet base could break. While securing the toilet, continue to check that the toilet is level.

Another expert advice for installing a new toilet is that the toilet should sit snugly on the floor. If it doesn’t, make up for the base with traces of lead flashing, available from roofing supply stores. Loosen the nuts slightly and push the compensating material in until the bowl of the toilet seats securely.

Trim bolt stops if they protrude too far; they may need to be cut with a metal saw or cutting disc. Press decorative covers over bolts.

Install the tank according to Hamilton Plumber

Place the rubber gasket gasket between the tank and bowl, place the rubber washers under the heads of the mounting bolts and place the tank over the toilet. Tighten the bolts, alternating from side to side until the tank is secured. Use a leveler to make sure the toilet is level.

With the tank already installed, connect the new feed tube to the shut-off valve. Use the correct size wrench to avoid damaging new fittings. Open the valve and check for leaks. Discharge the toilet and recheck for leaks and proper operation. Put silicone caulk on the floor of the toilet base. Install toilet seat as the hamilton plumber advices.

Tools and Materials You’ll Need to Install a New Toilet

  • Adjustable wrench or set of wrenches
  • Leveler
  • Metal Saw
  • Putty spatula
  • Bowl Wax Ring
  • Toilet retention bolts
  • Plastic bolt covers
  • Silicone gun and putty for kitchens and bathrooms
  • Plastic or protective sheeting
  • Padding to protect the new toilet
  • Sponges and rags